JVCC ATG-7502 ATG Tape: 1/4 in x 36 yds. (Clear Adhesive on Gold Liner)

JVCC ATG-7502 ATG Tape, like all ATG tapes, is reverse wound on the roll so it is designed to be used in an ATG dispenser/gun. Please see below for a matrix of which sizes of this tape fit into which ATG dispensers (not for use in all ATG dispensers)

Please see listing below to confirm which ATG refill rolls work in which ATG dispensers (you can also watch a YouTube video demonstrating the compatibility between ATG refill rolls and ATG guns).

JVCC ATG1 Dispenser -or- Scotch 700 Yellow Dispenser

• JVCC ATG-7502 (acid neutral): 1/4 x 36, 3/8 x 36, 1/2 x 36, 3/4 x 36
• JVCC ATG-7502X: 1/4 x 36, 1/2 x 36, 3/4 x 36
• JVCC ATG-7505: 1/4 x 18, 1/2 x 18, 3/4 x 18
• Scapa T002 (acid neutral): 1/2 x 36, 1/2 x 60, 3/4 x 60
• Scapa TD-200: 1/2 x 36, 3/4 x 36
• Scapa TD-500: 1/2 x 18, 3/4 x 18
• Scotch 908 (acid neutral): 1/2 x 36, 3/4 x 36
• Scotch 924: 1/2 x 36
• Scotch 928 (repositionable): 1/2 x 36
• Scotch 969: 1/2 x 18, 3/4 x 18

Scotch 085 Pink Glider -or- Scotch 714 Red Dispenser -or- Scotch 700A Adapter used in Scotch 700 Yellow Dispenser

• JVCC ATG-7502 (acid neutral): 1/4 x 36 *special core
• JVCC ATG-7502X: 1/4 x 36 *special core
• Scotch 908 (acid neutral): 1/4 x 36
• Scotch 924: 1/4 x 36
• Scotch 969: 1/4 x 18

JVCC ATG-7502 ATG Tape is a permanent unsupported acrylic adhesive transfer film (pressure-sensitive adhesive pre-applied to a special release liner). It is used for picture framing, scrapbooking, product assembly, and for design and packaging prototypes. Has good adhesion to paper, most plastic films, and metal foils. The manufacturer states this transfer tape is acid-neutral based on lab tests; however, there is no standardized test for pH for materials not soluble in water and this transfer tape is not soluble in water. Other features include:

• Glass stabilized solvent-based acrylic adhesive.
• On a 50# gold paper liner.
• Mounted on cores designed especially for use in tape dispensers (tape dispensing system allows for quick, clean, and easy application).

Application Instructions

For a visual guide to loading and using refill rolls in a JVCC ATG1 dispenser please see http://static.findtape.com/inserts/ATG-Loading-Instructions.pdf.

NOTES: Sizes shipped will typically be the tape industry standard metric-cut sizes, i.e. 24mm for each 1 inch of nominal tape width ordered (rolls are approximately 5% narrower than the nominal size). This product’s actual size is 6mm x 33m. As with any adhesive tape product it is always the user’s responsibility to determine that the product is suitable for their intended use; e.g. if you want to remove a product cleanly from a specific type of substrate please test on an inconspicuous area first. Warning: This product can expose you to chemicals including Toluene, which is [are] known to the State of California to cause birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov/.

Technical Information
– Core: 1 inch diameter plastic
– Backing/Carrier: N/A (Unsupported)
– Adhesive: solvent based acrylic
– Release Liner: 50# gold paper
– Thickness: 2 mils (carrier, adhesive)
– Adhesion: 27 ounces per inch (to stainless steel test panel)
– Service/Operating Temperature: -22F to 356F

• JVCC ATG-7502 ATG Tape, like all ATG tapes, is reverse wound on the roll so it is designed to be used in an ATG dispenser/gun.
• JVCC ATG-7502 ATG Tape is a permanent unsupported acrylic adhesive transfer film (pressure-sensitive adhesive pre-applied to a special release liner).
• It is used for picture framing, scrapbooking, product assembly, and for design and packaging prototypes.
• Has good adhesion to paper, most plastic films, and metal foils. The manufacturer states this transfer tape is acid-neutral based on lab tests; however, there is no standardized test for pH for materials not soluble in water and this transfer tape is not soluble in water.
• Carrier/Backing: N/A (Unsupported). Adhesive: solvent based acrylic. Release Liner: 50# gold paper. Thickness: 2 mils (carrier, adhesive). Adhesion: 27 ounces per inch (to stainless steel test panel). Service/Operating Temperature: -22F to 356F. Core: 1-inch diameter plastic.